Home page

Non-woven geotextile for landfill

Geotextile is usually made from a synthetic polymer such as polypropylene (PP), polyester (PET) etc. raw material and processed by woven & needle punched non woven or heat bonded methods. It is used as protection, filtration or separation layer alternative to diverse terrain such as soil, rock, sand and so on, also the UV Resistance and Thermal Bonded etc.

Classification :

Non-woven Geotextiles

+8613853470507

lingxiang@sdlxgeo.com

E-mail

PRODUCT DETAILS

Product introduction

The non-woven geotextile is made of filament or short fiber laid into a network through different equipment and processes. After needle punched and other processes, different fibers are interwoven and intertwined to make the fabric standardized,soft, full, thick and hard, so as to meet the requirements of different thickness.

The non-woven geotextile has good fabric gap and good adhesion due to the softness of the fiber, it has certain tear resistance, good deformation adaptability, and good plane drainage capacity. The surface is soft and multi gap, and has a good friction coefficient, which can increase the adhesion capacity of soil particles, prevent the loss of particles by preventing the loss of particles, and eliminate the excess water. The surface is soft and has good protection ability. According to the length of filament, it can be divided into filament non-woven geotextile or short filament non-woven geotextile. They can play a very good filtration, isolation, reinforcement, protection and other effects, is a widely used geosynthetics. The tensile strength of filament is higher than that of staple, so it can be used according to specific requirements.

Non-woven geotextiles are multi-purpose fabrics that are felt-like in appearance. The important functions for this merchandise are filtration and separation. The most frequent non-woven is a needle-punched product. Staple fibers or continuous filaments are bonded via automatically entangling the fibers with barbed needles. It can save installation time is an economical alternative to other geosynthetics. The raw material offers the most cost-effective range of geotextiles bringing the maximum value to your project, this range of non-woven geotextiles offers excellent energy absorption characteristics as well as superior filtration performance.

Performance characteristics

High strength, due to the use of plastic fibers, it can maintain full strength and elongation in dry and wet condition.

Corrosion-resistant, long-lasting corrosion-resistant in mud/soil water of different acidity and alkalinity.

Good water permeability, there are voids between the fibers, so it has good water permeability.

Good anti-microbial properties, microorganisms, insects are not damaged.

Convenient construction, because the material is light and soft, so it is convenient for transportation, laying and construction.

Light weight, low cost, corrosion resistance, anti-filtration, drainage, isolation, enhancement and other good properties.

Technical indicators

Item	Specification
Item	100	150	200	250	300	350	400	450	500	600	800	note
Mass deviation per unit area	-8	-8	-8	-8	-7	-7	-7	-7	-6	-6	-6
thicknesses	0.9	1.3	1.7	2.1	2.4	2.7	3.0	3.3	3.6	4.1	5.0
Width deviation	-0.5
breaking strength KN/m≥	2.5	4.5	6.5	8.0	9.5	11.0	12.5	14.0	16.0	19.0	25.0	vertically and horizontally
Elongation at break %	25~100
CBR Top Break Power kN≥	0.3	0.6	0.9	1.2	1.5	1.8	2.1	2.4	2.7	3.2	4.0
tearing force kN≥	0.08	0.12	0.16	0.20	0.24	0.28	0.33	0.38	0.42	0.46	0.60	vertically and horizontally
equivalent pore size	0.07~0.2
vertical permeability coefficient	Kx(10-2~10-3)											K=1.0~9.9

New standard for geotextile ( GB/T 17638- 2017 )

Item		Nominal breaking strength /(kN/m)
Item		3	5	8	10	15	20	25	30	40
1	Longitudinal and transverse rupture strength /(KN/m)≥	3.0	5.0	8.0	10.0	15.0	20.0	25.0	30.0	40.0
2	Nominal breaking strength corresponding to the elongation /%	20-100
3	damaged by groundless slander /kN ≥	0.6	1.0	1.4	1.8	2.5	3.2	4.0	5.5	7.0
4	Quality deviation rate per unit area /%	±5
5	Width deviation rate %	-0.5
6	Thickness deviation rate %	±10
7	equivalent pore size O3o(O3s)/mm	0.07-0.20
8	vertical permeability coefficient cm/s	Kx(10¹-10³) where: K=1.0-9.9
9	vertical and horizontal tearing /kN≥	0.10	0.15	0.20	0.25	0.40	0.50	0.65	0.80	1.00
10	Acid and alkali resistance (strength retention) %≥	80
11	Oxidation resistance (strength retention) %≥	80
12	UV resistance (strength retention) %≥	80

FACTORY APPEARANCE

The company now has an independent R&D center and has established technical cooperation relationships with many well-known domestic universities and scientific research institutions. The company has nine modern production workshops, nearly 20 production lines, and an annual production capacity of more than 30,000 tons.

HONOR

The company now has an independent R&D center and has established technical cooperation relationships with many well-known domestic universities and scientific research institutions.

CONSTRUCTION CASES

Since its establishment, the company has provided services for China's South-to-North Water Diversion Project, Sanjiang Management Project, Shanxi Railway Channel Project, Ningxi Railway Project, Gansu Expressway Project, Shijiazhuang Subway Project, Shenyang Landfill Seepage Prevention Project, and Binzhou Landfill Prevention Project.

South-to-North Water Diversion Project Middle Line Project

Sanjiang Management Project

Inner Mongolia Yellow River Diversion Project

Qingge River Flood Diversion Project of China Water Resources No. 13 Bureau

Gansu Province Jishishan Water Diversion Project

Ningxia Hui Autonomous Region Jingyuan Reservoir Project

Rizhao Lanqiao Railway Dam Project

Xinjiang Aksu Engineering Composite Membrane Procurement Project of China Water Resources No.4 Bureau

FAQ

Q: Can we take some samples? Any fees?

A: Yes, we can provide samples free of charge, but we don't pay for shipping. If you place an order after confirming the sample, we will refund your delivery fee or deduct it from the order amount.

Q:Can you deliver the goods on time?

A: Yes, we guarantee the best quality products and punctual delivery. Integrity is the tenet of our company.

Q: What are the loading ports?

A: In general, we ship the goods from Shanghai, Tianjin, Qingdao and Ningbo ports. You can designate other ports according to your needs.

Q: Is there quality inspection before loading?

A: Of course, all our products go through strict quality inspection before packing. Those that fail will be destroyed. Customers can also entrust a third party to inspect the products before loading.

Q: How is the product packaged?

A: Standard export seaworthy packing with waterproof paper inside and iron outside, secured by fumigated wooden pallets. It can effectively protect products from corrosion and various climate changes during Marine transportation.